Bicycle attached to a car rack
|

How to Install a Bike Rack on an SUV (Hitch Rack Step-by-Step)

JupiterVehicles is reader-supported. As an Amazon Associate, we earn from qualifying purchases.

A hitch rack is the most common bike rack on SUVs, and installing one usually takes 10 to 15 minutes without special tools. Here’s how to do it right. If you’re still deciding which rack type to use, see how to attach a bike rack to an SUV.

Always follow the instructions that came with your rack. Steps vary between brands.

What You Need

  • A hitch rack that matches your receiver size (1-1/4 or 2 inches)
  • The hitch pin, bolt or locking knob that came with the rack
  • A wrench, if your rack uses a threaded bolt
  • A helper, for lifting heavy racks

Step 1: Check Your Hitch

Look at your receiver opening and the class label on the hitch. CURT’s hitch class guide shows Class 1 and 2 hitches use 1-1/4 inch receivers, while Class 3 and 4 use 2-inch receivers. Make sure the rack plus your bikes stays within the hitch’s tongue weight rating.

No hitch? A hitch receiver can usually be added to an SUV. Many owners have it installed by a shop.

Step 2: Assemble the Rack

Most racks come partly assembled. Attach the trays or arms to the mast as the instructions describe, and tighten all bolts.

Step 3: Insert the Rack Into the Receiver

  1. Clean any dirt out of the receiver.
  2. Lift the rack and slide the mast into the receiver.
  3. Line up the hole in the mast with the hole in the receiver.

Step 4: Secure It

  • Pin and clip: Push the pin through and secure it with the clip or lock.
  • Threaded bolt: Thread the bolt through and tighten it with a wrench.
  • Tool-free knob: Turn the knob until tight. Many racks have an expanding wedge inside the mast to reduce movement.

Thule’s hitch rack wobble guide recommends pressing the rack toward the vehicle and slightly up so it’s level and fully seated while someone else tightens it.

Step 5: Test It

Grab the rack and push it side to side. Thule notes that some vertical movement is normal and acts like a shock absorber, but the rack should be mostly still side to side. If it isn’t, retighten it.

Step 6: Check Clearance and Lighting

  • Make sure the rack doesn’t block your license plate or lights. If it does, you may need a light board or plate relocator, depending on your state’s rules.
  • Tilt the rack down to confirm the rear hatch can open, if your rack has that feature.

Step 7: Recheck on the Road

Thule recommends checking the rack’s tension every 200 miles and retightening as needed.

Sale
Thule Outpace 2 Bike Hitch Rack, 2" & 1.25" Hitch, 110lb Capacity | OutPace Bike Rack - Compact Foldable Hitch Mount for 2 Bikes
  • Supports a wide range of bike frame geometries and tube diameters from 0.8 to 3.5 in. (20 to 90 mm)
  • Moveable head that rotates, slides, and adjusts flexibly to fit different bike sizes and styles, making sure it always finds the perfect position on the frame
  • You can load and unload up to two bikes in any order – all types of frames and geometries are supported
  • Folds into a compact unit for easy storage in tight spaces
  • Carrier tilts down to allow access to the trunk at all times

The Thule Outpace 2 (about $600) fits both 2-inch and 1-1/4 inch hitches. Compare more options in our best hitch bike rack guide, then see how to put a bike on a bike rack.

FAQ

Can I install a hitch bike rack myself?

Yes. If your SUV already has a hitch receiver, most racks install in minutes. Installing the hitch receiver itself is a bigger job that many people leave to a shop.

Why does my hitch bike rack wobble?

It may not be fully seated or tightened. Thule says some vertical movement is normal, but side-to-side movement should be minimal.

Do I need a hitch lock?

It’s a good idea. A locking pin or knob stops someone from removing the rack.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *